Make your own jigs & hold-downs. Excellent for attaching feather boards, hold-downs, and special jigs to your table saw, router table, disc sander, or any other tool with a standard 3/4' wide x 3/8' deep miter gauge slot. Poker can a straight wrap around blouse. The bars pull up tight in the slot as you tighten the knobs. These square-slot Bars fit both square and t-shaped miter gauge. UHMW Precision Milled Bar 3/4' X 3/8' X 36' For Jigs, Fixtures or Miter Slots (size 3/4' x 3/8'). Slick Durable Material Slides with Ease. Ideal for Table Saws, Router Table and Bandsaws (2 UHMW Bars) 4.3 out of 5 stars 177.
Introduction: MITER SLED FOR SMALL TABLE SAW
My Little Shop of Jarfold has a new small table saw (23' x 20' top) for which I'll be needing some new jigs. I built a small miter jig using scraps of 3/4' plywood and some thinner scraps for the runners.
Step 1: BASE AND RUNNERS
Brittany page poker. I ripped down some scrap wood to EXACTLY fit the slots on the table saw. A few coins held the guides proud of the slots. I glued and screwed the plywood base to the runners. There was absolutely no wiggle to the base in the slots.
Step 2: CUT SLOT
I cut a slot about halfway through the base with the full height of the blade. I glued together pieces of scrap plywood for the miter guides a tad lower than the full height of the blade.
Step 3: THE MITER GUIDES
Table Saw Miter Slot Size
I marked a line 45 degrees to the blade. I glued and screwed one guide on this line. I trimmed off the overhang. Using a rafter's square, I glued and screwed the other side of the guide. As long as the two sides are exact right angles to each other and you cut one miter on the left and its match on the right, the fits will always be perfect.
Step 4: SAW BLADE GUARD
They call it an accident because it is. They don't call it an ON PURPOSE! So, for safety I glued together some scrap and made a wedge higher than the full height of my raised blade and glued it in place.
Step 5: TESTING THE CUTS
I cut 4 equally long pieces of scrap and mitered the left side. I set up a stop and mitered the right side. It went together perfectly. However, there was one more thing I wanted to add. Something to hold the open kerf at the beginning of the sled in place.
Step 6: FRONT STABILIZER
I added a stabilizer at the front of the sled and ran the blade through it. This, too, was higher than the full extension of the blade. At this point, the sled was done. Let it be noted that this sled has a capacity of cutting 3' wide boards, which is fine for my needs. To cut much wider boards, add more space between the front stabilizer and the miter guides.
Step 7: THANKS FOR STOPPING IN
I know there are many miter sled How-Tos out there, but most are for huge floor model table saws. For those like me and have a small table saw, I hope this helps.
Military themed tattoo sleeves. Jan 30, 2020 - Explore Chris Focus's board 'casino tattoos' on Pinterest. See more ideas about casino tattoo, tattoos, sleeve tattoos.
Drop a comment or ask a question. I'd love to hear from you.
I marked a line 45 degrees to the blade. I glued and screwed one guide on this line. I trimmed off the overhang. Using a rafter's square, I glued and screwed the other side of the guide. As long as the two sides are exact right angles to each other and you cut one miter on the left and its match on the right, the fits will always be perfect.
Step 4: SAW BLADE GUARD
They call it an accident because it is. They don't call it an ON PURPOSE! So, for safety I glued together some scrap and made a wedge higher than the full height of my raised blade and glued it in place.
Step 5: TESTING THE CUTS
I cut 4 equally long pieces of scrap and mitered the left side. I set up a stop and mitered the right side. It went together perfectly. However, there was one more thing I wanted to add. Something to hold the open kerf at the beginning of the sled in place.
Step 6: FRONT STABILIZER
I added a stabilizer at the front of the sled and ran the blade through it. This, too, was higher than the full extension of the blade. At this point, the sled was done. Let it be noted that this sled has a capacity of cutting 3' wide boards, which is fine for my needs. To cut much wider boards, add more space between the front stabilizer and the miter guides.
Step 7: THANKS FOR STOPPING IN
I know there are many miter sled How-Tos out there, but most are for huge floor model table saws. For those like me and have a small table saw, I hope this helps.
Military themed tattoo sleeves. Jan 30, 2020 - Explore Chris Focus's board 'casino tattoos' on Pinterest. See more ideas about casino tattoo, tattoos, sleeve tattoos.
Drop a comment or ask a question. I'd love to hear from you.
1 Person Made This Project!
- superkoreanr6s made it!
Recommendations
Dewalt Table Saw Miter Slot
Table Saw Miter Slot Runners Depot
Anything Goes Contest
Plastic Contest
Battery Powered Contest
If you're planning on making a sliding jig or fixture for your woodworking shop, the INCRA Miter Slider is exactly what you need. These inexpensive aluminum runners adjust for PERFECT sliding action in any standard (or near standard) 3/4' by 3/8' miter gauge slot with just a twist of the wrist. They lock firmly in place with another twist of the wrist. Won't warp, shrink or swell like wooden runners. Includes plans for a wide variety of shop-made jigs and fixtures. Anodized aluminum for durability and beauty. Available in 18' and 24' lengths.
- Adjusts for perfect sliding action in any standard miter gauge slot with just a twist of the wrist
- Locks securely in any standard miter gauge slot with another twist of the wrist
- Includes threaded mounting holes and hardware for easy attachment to any application
- Includes plans for a wide variety of shop-made jigs and fixtures
- All mounting hardware included
